Microtek ArtixScanTS 630S Bedienungsanleitung

MicrotekArtixScan 1800fInstallation and Operation Manual

6 ArtixScan 1800f Installation and Operation ManualInstallationThis section provides information on the scanner connection procedures.Installing t

ArtixScan 1800f Installation and Operation Manual 7Connecting the Scanner to Your ComputerThe ArtixScan 1800f comes with both FireWire and USB 2.0

8 ArtixScan 1800f Installation and Operation Manual2. Connect the scanner to your computer, using the provided FireWire cable.Connect one end of t

ArtixScan 1800f Installation and Operation Manual 9Using the USB 2.0 CableThe ArtixScan 1800f's USB interface is a Hi-Speed USB 2.0 support p

10 ArtixScan 1800f Installation and Operation ManualFor PC users(with a Hi-Speed USB 2.0 card installed)For PC users(with a built-in USB port)3. P

ArtixScan 1800f Installation and Operation Manual 11Positioning Your OriginalsThis section provides information on how to position your originals

12 ArtixScan 1800f Installation and Operation ManualPositioning Transparent FilmThis procedure applies when you use the lower scan bed of the Art

ArtixScan 1800f Installation and Operation Manual 13RRUsing the Glass HolderTo scan large or non-standard-sized transparencies:1. Place the film f

14 ArtixScan 1800f Installation and Operation ManualUsing the Other Film HoldersUse the other film holders together with the Main Holder for scann

ArtixScan 1800f Installation and Operation Manual 15A. Using the 35mm Slide HolderThe 35mm Slide Holder can hold a maximum of twelve mounted slide

iiCopyright © 2002 by Microtek International, Inc.All rights reserved.TrademarksMicrotek®, ArtixScanTM, and ScanWizardTM Pro are trademarks or registe

16 ArtixScan 1800f Installation and Operation Manualc) Align the frame-by-framepartition on your filmstrip withthe Arrow mark of the holder.d) Sna

ArtixScan 1800f Installation and Operation Manual 171.11.22.22.1C. Using the 6 x 9 cm Film HolderThe 6 x 9 cm Film Holder can hold four transparen

18 ArtixScan 1800f Installation and Operation Manual1.11.2D. Using the 4" x 5" Film HolderThe 4" x 5" Film Holder can hold two

ArtixScan 1800f Installation and Operation Manual 19Your First Scan1. Launch ScanWizard Pro from your image editing application. To do this, choos

20 ArtixScan 1800f Installation and Operation Manual3. Click the Overview button to start an overview, and you will see the image appearin your Pr

ArtixScan 1800f Installation and Operation Manual 21Performing Color CalibrationThe Microtek Scanner ICC Profiler (MSP) is a scanner calibration a

22 ArtixScan 1800f Installation and Operation ManualA. Positioning the Reflective Target1. Place the target face down on the glass surface of the

ArtixScan 1800f Installation and Operation Manual 23Calibrating Your Target1. With the target properly positioned in the scanner, turn on your sca

24 ArtixScan 1800f Installation and Operation ManualLoading a ProfileOnce the profile has been produced, follow the steps below to load the profil

ArtixScan 1800f Installation and Operation Manual 25SpecificationsInterfaces 2 FireWire (IEEE-1394) ports, one USB/USB 2.0 portDynamic Range 4.8 D

iiiContentsIntroduction 1System Requirements ... 1Environmental Requirements ...

26 ArtixScan 1800f Installation and Operation ManualFederal Communications Commission Interference StatementThis equipment has been tested and fou

iv

ArtixScan 1800f Installation and Operation Manual 1IntroductionThe ArtixScan 1800f is a single-pass, dual interface (FireWire and USB 2.0), 48-bit

2 ArtixScan 1800f Installation and Operation ManualEnvironmental RequirementsBefore unpacking your scanner, make sure that the location where the

ArtixScan 1800f Installation and Operation Manual 3Unpacking the ScannerWhile unpacking the scanner, inspect the shipping carton for any signs ofm

4 ArtixScan 1800f Installation and Operation ManualHorizontal rulerScanner lidGlass surface(Upper scan bed)Vertical rulerTaking a closer lookTrans

ArtixScan 1800f Installation and Operation Manual 5Unlocking the ScannerBefore you start to operate the scanner, the scanner should be unlocked. T