Microtek MX3 Spezifikationen

Turning on the projector1. Remove the lens cover.2. Make sure the signal cables are connected.3. Plug-in the power cord; the LED indicator will flash

3.3 Adjusting the height of the projected imagePlease use the foot adjuster to adjust the height of the projector.Higher1. Hold the foot adjuster butt

3.4 Adjusting the focus and zoomYou can zoom in or zoom out the image with the zoom ring. To enlarge the imagesize, turn the zoom ring counterclockwis

3.5 Projected Image SizeDistance to Screen 55” 78” 157” 236” 393”Minimum Screen Size 35” 49” 99” 149” 248”Maximum Screen Size 41” 58” 116” 174” 290”ＭＸ

4. How to use the projectorThis section covers how to use and adjust the projector, as well as how to usethe control panel, remote control, and menu.4

LED Indicator When the projector is turned on, the LED indicator flashes. Press the Standbykey to display the image. After a few moments, the LED ind

- Remote ControlKey FunctionsFreeze/Esc/L  Press this key to freeze the image. Press again to clearthe static image. Press this key to quit the menu

Menu  Please refer to page 13, “Menu” of “Control panel”.Source  Select Analog RGB, Analog Y Pb Pr, Digital RGB,Composite Video, S-Video and Compone

5. MenuPress the Menu key to open the menu. You can press the up or down key to select theitems on the menu; or press Esc to quit the menu. To enter t

5.2 Image (Video mode)* Press the Auto key to return to previous setup.Submenu Purpose UsingBrightness To adjust the brightness of  Press  key to de

122346689101112121212141616171819202122232323242426Table of Contents1. Safety Instructions2. The Projector2.1 Features2.2 Accessories2.3 Appearance3.

5.3 Display (VGA mode)Submenu Purpose UsingFrequency To adjust the frequency of Press   key fordata display to be the same adjustment (*)as the fre

5.4 Display (Video mode)Submenu Purpose UsingKeystone To modify the biased image  Press  key to reduceresulting from the improper the length of the

5.5 AudioSubmenu Purpose or UsingVolume  Press  key to turn down the volume. Press  key to turn up the volume.(*)Treble  Press  key to decrease

5.6 ManagementSubmenu Purpose UsingOSD Location To display the position of the  Press   key formenu on the screen. selection (*)Projection

Lamp Reset To recount hours after replacing  Press the right key. Thethe lamp. message “Press Enterkey to confirm lampreset operation!”appears. Pleas

6. Maintenance6.1 Replacing the lamp30 hours before the end of the lamp’s life time, the warning message “Lamp lifetime is up! Replacement suggested!

7. Appendix7.1 Common problems and troubleshootingIf you are having a problem with your projector, please check the following situ-ations described be

Q.: Image becomes blurred Adjust the focus ring of the projector. Make sure that distance between the screen and projector is adequate (4’7”~ 32’9”

7.2 SpecificationsResolution XGA (1024*768), SXGA (1280*1024) compressedLamp 150W VIP, 1500 hrs lamp lifeBrightness 1500 ANSI LumensSize 229x193x69 mm

Input Terminal DVI (M1DA)  USB  RGB (M1DA-D-Sub 15 pin) RS232 (M1DA)  Y/Pb/Pr (M1DA,VGA)  S-Video Mini DIN 4 pin Audio: RCA Jack  3.5mm Mini J

1. Safety instructionsBefore you use the projector, please read this manual thoroughly andcomply with the safety instructions hereunder. Improper use

2. The projector2.1 Features Receives signals with resolution up to 1280x1024,75 Hz. To ensure the out-put quality, please adjust the setup of your c

2.2 AccessoriesPlease check if the following accessories are in the box. If any item ismissing, please contact your dealer immediately.Projector with

Control panel2.3 ComponentsZoom RingFocus RingLens coverMain BodyInfrared Remote ReceiverSpeakerVideo EnhancedAdapterScrewＭＸ３　ｍａｎｕａｌ．ｐ６５ 02-12-17, 16:

Foot AdjusterFoot Adjuster buttonＭＸ３　ｍａｎｕａｌ．ｐ６５ 02-12-17, 16:396

3. Setting up the projector3.1 How to connect the projectorDepending on your purpose, you can select any of the following connectionmethods.1) For dis

Use the Video Enhanced Adapter, and choose from the terminals be-low to connect.3.2 Turning on/off the projector1. Power cord2. VGA signal input termi